Panasonic WJMP204 Betriebsanleitung PDF herunterladen (Seite 18)

■ System Setup for Camera

Communication Mode

1. Display the Setup menu.

2. Move the cursor to SYSTEM by pressing button 1 (C)

or button 2 (D), then press the SUSPEND/SET button.

• In case of Camera Communication mode, the SYS-

TEM menu appears as shown below.

SYSTEM

ALARM MODE ON

COMP/VD2/DATA

VS/VD INPUT VD

DAISY MODE ON

TERMINAL ALARM

3. Move the cursor to the desired item by pressing button

1 (C) or button 2 (D), and then select the desired

mode by pressing button 3 (–) or button 4 (+).

4. Press the SUSPEND/SET button.

5. After taking the above steps, press the SETUP/ESC

button for 2 seconds or more.

Note: All the settings must be compatible with the

peripherals connected.

(1) Alarm Mode Setting

• Monitor Spot Setting

1. Display the SYSTEM menu.

2. Move the cursor to ALARM MODE by pressing button 1

then select MONITOR SPOT ON or OFF by pressing

button 3 (–) or button 4 (+).

The initial factory setting is ON.

ON: The screen of the corresponding channel appears

on the spot output screen when the alarm is activat-

ed.

OFF: The screen continues to display the pictures in

the mode selected previously when the alarm is

activated.

• Alarm Display Setting

1. Display the SYSTEM menu.

2. Move the cursor to ALARM DISPLAY by pressing button

1 (C) or button 2 (D), then select ALARM DISPLAY ON

or OFF by pressing button 3 (–) or button 4 (+) so that

[ALARM∗∗∗] appears on the screen or not.

The initial factory setting is ON.

Note: The figure shown in the place of [∗∗∗] after the

word ALARM is a channel number.

• Site Alarm Setting

1. Display the SYSTEM menu.

2. Move the cursor to SITE ALARM by pressing button 1

OFF by pressing button 3 (–) or button 4 (+).

The initial factory setting is ON.

• Terminal Alarm Setting

1. Display the SYSTEM menu.

2. Move the cursor to TERM. ALARM by pressing button 1

OFF by pressing button 3 (–) or button 4 (+).

The initial factory setting is ON.

• Alarm Output Data (Alarm Output Duration from

Alarm Connector)

1. Display the SYSTEM menu.

2. Move the cursor to ALARM OUTPUT by pressing button

1 (C) or button 2 (D), then select the desired alarm

output duration, 1S - 30S, 40S, 50S, 1MIN, 2MIN, 3MIN,

4MIN, 5MIN, EXT or OFF, by pressing button 3 (–) or

button 4 (+).

The initial factory setting is 10S. Enable to set by 1 sec-

ond (1S - 30S).

EXT: The alarm signal continues to be output from

ALARM/REMOTE connector till the alarm is

reset. The alarm is not automatically reset.

1S-5MIN: The alarm signal is supplied from ALARM/

REMOTE connector only for the set time. The

alarm is automatically reset after the set time.

(The ALARM indicator changes from blink to

steady light.)

OFF: The alarm signal is not supplied from ALARM/

REMOTE connector. The alarm is not auto-

matically reset.

ALARM MODE

MONITOR SPOT ON

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM DATA AUTO2

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Panasonic WJMP204 Betriebsanleitung Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitskameras Panasonic WJMP204