Panasonic WJMP204 Betriebsanleitung PDF herunterladen (Seite 15)

(2) Comp/VD2/Data Setting

• Camera Input Setting

1. Display the SYSTEM menu.

2. Move the cursor to CAMERA IN by pressing button 1

then select the desired channel 1, 2, 3 or 4 for back-

ground picture by pressing button 3 (–) or button 4 (+).

The initial factory setting is 1CH.

• Cable Compensation Setting

1. Display the SYSTEM menu.

2. Move the cursor to COMP by pressing button 1 (C) or

button 2 (D), press the SUSPEND/SET button, then

select the most suitable cable length by pressing but-

ton 3 (–) or button 4 (+).

S: Less than 400 m (1,300 ft)

M: 400 m (1,300 ft) to 700 m (2,300 ft)

L: 700 m (2,300 ft) to 900 m (3,000 ft)

(When using RG-59U, BELDEN 9259 or equivalent

cable)

The initial factory setting is S.

• VD2 Setting

1. Display the SYSTEM menu.

2. Move the cursor to VD2 by pressing button 1 (C) or

button 2 (D), press the SUSPEND/SET button, then

select ON, OFF, or THRU by pressing button 3 (–) or

button 4 (+).

ON: Multiplex sync signals (VD2) are generated by

synchronizing with the signals sent to the VS/VD IN

connector. If there is no input signal, the internally

generated sync signal (VD2) is multiplexed.

OFF: Sync signal (VD2) is not multiplexed.

THRU: The sync signal (VD2) sent to the CAMERA

OUT connector is multiplexed with the video sig-

nals. If there is no input signal, the sync signal

(VD2) is not multiplexed.

The initial factory setting is ON.

• Data Setting

1. Display the SYSTEM menu.

2. Move the cursor to DATA by pressing button 1 (C) or

button 2 (D), press the SUSPEND/SET button, then

select data communication ON or OFF by pressing but-

ton 3 (–) or button 4 (+).

1. Display the SYSTEM menu.

2. Move the cursor to CAMERA CONFIG by pressing but-

ton 1 (C) or button 2 (D), press the SUSPEND/SET

button, then assign unit numbers, 1 to 128 or - (no

camera), by pressing button 3 (–) or button 4 (+).

Camera numbers are automatically assigned accord-

ing to the UNIT switch settings.

(5) Daisy Mode

1. Display the SYSTEM menu.

2. Move the cursor to DAISY MODE by pressing button 1

OFF by pressing button 3 (–) or button 4 (+).

The initial factory setting is ON.

(6) Terminal

1. Display the SYSTEM menu.

2. Move the cursor to TERMINAL by pressing button 1

pressing button 3 (–) or button 4 (+).

The initial factory setting is ALARM.

Note: To switch from ALARM/REMOTE IN to ALARM/

REMOTE OUT, shift the internal connector of the WJ-

MP204 from the ALM IN connector to the ALM OUT

connector (See page 24).

The initial factory setting of ALARM/REMOTE connector

is ALM IN.

COMP/VD2/DATA

CAMERA IN 1CH

COMP S

VD2 ON

DATA ON

CAMERA CONFIG

CAMERA IN CAM NO.

1CH 1CH

2CH 2CH

3CH 3CH

4CH 4CH

The initial factory setting is ON.

(3) VS/VD Input

1. Display the SYSTEM menu.

2. Move the cursor to VS/VD INPUT by pressing button 1

button 3 (–) or button 4 (+).

The initial factory setting is VD.

(4) Camera Config

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Panasonic WJMP204 Betriebsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitskameras Panasonic WJMP204