
● How to Insert the Batteries
1
Slide down the remote control cover completely
to remove it.
2
Insert the batteries
– Be sure the direction is correct
– 12:00 on display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
3
Re-install the remote control cover by inserting it
in the side groves and pushing inward.
● About the batteries
• Can be used for approximately one year.
● Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
C
H
E
C
K
AUTO
O
F
AUTOHEAT
DRY
FANCOOL
FAN
AUTO
AUTO
R
E
S
E
T
C
L
O
C
K
A
I
R
S
W
I
N
G
O
F
F
C
A
N
C
E
L
1
2
3
T
IM
E
R
P
O
W
E
R
F
U
L
A
U
T
O
M
A
N
U
A
L
E
C
O
N
O
M
Y
O
N
S
ET
F
A
N
S
P
E
E
D
M
O
D
E
2
1
1.5V
1.5V
NAME OF EACH PART
■ Remote Control
● Remote Control Signal
• Make sure it is not obstructed.
• Maximum distance : 10 m (32.8 ft.).
• Signal received sound :
One short beep or one long beep.
● Notes for Remote Control
• Do not throw or drop.
• Do not get it wet.
• Certain types of fluorescent lamps may affect
signal reception. Consult your dealer.
CHECK
TEMP
AUTAUTO
ON
OFF
AUTAUTOHEAHEAT
DRYFAN
F
COOLCOOL
FANAN
AUTAUTO
RESET CLOCK
MODE
POWERFUL
ECONOMY
FAN SPEED
AIR SWING
OFF
CANCEL
ON
SET
1
2
3
TIMER
OFF/ON
QUIET
AUTO
MANUAL
#
!
$
%
^
$
*
&
3
5
8
7
9
0
6
4
(
2
1
1 Signal Transmitter
2 Operation Display
3 Quiet Mode Operation Button
4 Room Temperature Setting Button
(Illuminating button)
5 Operation Mode Selection Button
6 Economy Mode Operation Button
7 Auto Airflow Direction Button
8 ON-Timer Button
9 OFF-Timer Button
0 Reset Point
(Press with fine-tipped object to clear the memory)
! OFF/ON Button
(Illuminating button)
@ Powerful Mode Operation Button
# Fan Speed Selection Button
$ Manual Airflow Direction Selection Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
PREPARATION BEFORE OPERATION
■ Indoor Unit
1
Open the front panel
2
Remove the air filters
3
Fit the air purifying filters in place
4
Insert the air filters
5
Close the front panel
■ Remote Control – To set the current time
1
Press 1.
2
Then press 2 to increase or decrease the time.
3
Press 1 again.
Set time on display will light up.
CHECK
AUTO
AUTO HEAT DRY FANCOOL
FAN
AUTO
RESET CLOCK
FAN SPEED
AIR SWING
OFF
CANCEL
ON
SET
1
2
3
TIMER
AUTO
MANUAL
1
2
5
1
3
4
2
Operation
Cooling
Soft Dry
Cooling Model
COOL –> 75°F ~ 78°F
DRY –> 2°F ~ 4°F
lower than the
room temperature
HOW TO OPERATE
■ To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
■ Setting Mode
• Press 2 to select:-
Cooling Model
AUTO – Automatic Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Air Circulation Operation
Heat Pump Model
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
Operation
Cooling
Soft Dry
Heating
Indoor
temperature
73°F
68°F
■ Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 60°F ~ 86°F.
• Recommended temperature:
• During AUTO Operation, press 3 to select:-
• Operation with 4°F higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 4°F lower than the standard
temperature.
● Standard Temperature
Cooling Model
• Once the Automatic Operation is selected, the indoor
temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.
• After the operation mode has been selected, the
mode does not change.
Heat Pump Model
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.
Standard
temperature
77°F
72°F
Standard
temperature
77°F
72°F
70°F
Indoor
temperature
73°F
O
F
F
O
N
H
E
A
HEAT
D
R
DRY
FA
N
ANC
O
O
L
COOL
C
H
E
C
K
T
E
M
P
A
U
T
AUTO
A
U
T
AUT
O
FA
N
AN
AU
T
AUTO
R
E
S
E
T
C
L
O
C
K
A
IR
S
W
IN
G
OFF
C
A
N
C
E
L
1
2
3
T
I
M
ER
O
F
F
/
O
N
Q
U
I
E
T
A
U
T
O
M
A
N
U
A
L
E
C
O
N
O
M
Y
POWERFUL
ON
S
E
T
FAN SPEED
M
O
D
E
2
3
5
1
6
4
Heat Pump Model
COOL –> 75°F ~ 78°F
DRY –> 2°F ~ 4°F
lower than the
room temperature
HEAT –> 68°F ~ 75°F
36
CS-A9CKPG CU-A9CKP6G / CS-A12CKPG CU-A12CKP6G
Kommentare zu diesen Handbüchern