Panasonic DMPBD85 Bedienungsanleitung PDF herunterladen (Seite 32)

VQT2H79

ReferenceReference

Troubleshooting guide

Before requesting service, please perform the

following steps.

The following do not indicate a problem with this unit:

≥ Regular disc rotating sounds.

≥ Image disturbance during search.

∫ Unit doesn’t respond to remote control

or front panel buttons.

Press and hold [Í/I] on the main unit for 3 seconds.

– If still unable to turn the unit off, disconnect the AC mains

lead, wait 1 minute, then reconnect the AC mains lead.

∫ Cannot eject disc.

The unit may have a problem.

1 While the unit is off, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1](right) on the remote control or [Í/I]

on the unit until “06 FTO” is displayed on the unit's

display.

3 Press [OK] on the remote control or [< OPEN/CLOSE] on

the unit.

To return to the factory preset.

Select “Yes” in “Default Settings” in the Setup menu. (

31)

To return all settings to the factory preset.

Reset the unit as follows:

1 While the unit is off, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1](right) on the remote control or [Í/I]

on the unit until “08 FIN” is displayed on the unit's display.

3 Press and hold [OK] on the remote control or [< OPEN/

CLOSE] on the unit for at least 3 seconds.

Power of this unit is turned off when the input

for the TV is switched.

This is a normal phenomenon when using VIERA Link

(HDAVI Control 4 or later). For details please read the

operating instructions for the TV.

The remote control doesn’t work properly.

The remote control and main unit are using different

codes. If “SET 1” , “SET 2” or “SET 3” is displayed when a

button is pressed on the remote control, change the code

on the remote control. (> 31)

It may be necessary to set the manufacturer code or the

remote control code again after changing the batteries for

remote control. (> 14)

The TV tuner mode is not displayed when the

TV is switched on.

This phenomenon may occur, depending on the TV

setting, when “Quick Start” is set to “On”.

– Depending on the TV, this phenomenon may be prevented

by reconnecting the HDMI cable to a different HDMI input

terminal or by changing the HDMI auto connection setting.

You have forgotten your ratings password.

You want to cancel the ratings level.

The ratings level returns to the factory preset.

1 While the unit is on, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1] (right) on the remote control or [Í/

I] on the unit until “03 VL” is displayed on the unit's

display.

3 Press [OK] on the remote control or [< OPEN/CLOSE] on

the unit.

The images from this unit do not appear on

the television.

Picture is distorted.

An incorrect resolution is selected in “Component

Resolution” or “HDMI Video Format”. Reset the setting as

follows:

1 While the unit is on, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– "00 RET” is displayed on the unit’s display.

2 Repeatedly press [1](right) on the remote control or [Í/I]

on the unit until “04 PRG” is displayed on the unit's

display.

3 Press and hold [OK] on the remote control or [< OPEN/

CLOSE] on the unit for at least 3 seconds.

Set the item again. (> 30)

– When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio

are not output in bitstream, select “Yes” in “Default Settings”

and make proper settings. (> 31)

The unit and television are using different video systems.

While stopped, keep pressing [∫] and [< OPEN/CLOSE]

on the main unit for 5 or more seconds. The system

switches from PAL to

NTSC

or vice versa.

The system used on the disc doesn’t match your

television.

– PAL discs cannot be correctly viewed on an NTSC

television.

– This unit can convert NTSC signals to PAL60 for viewing

on a PAL television (“NTSC Contents Output” in the

“Picture”).

Video is not output.

Set the “High Clarity Sound” in the playback menu to “Off”

to use the COMPONENT VIDEO OUT terminal or the

VIDEO OUT terminal. (> 27)

Do you have the latest firmware installed?

Firmware updates may be released to correct operating

irregularities that are discovered with certain movies.

(> 14)

Make the following checks.

If the problem remains unresolved, consult

your dealer for instructions.

General operation

Picture

DMP-BD85EB&EG-VQT2H79_eng.book 32 ページ２０１０年１月１５日　金曜日　午後６時４６分

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

Panasonic DMPBD85 Bedienungsanleitung Seite 32

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Blu-Ray-Player Panasonic DMPBD85