Panasonic WV-NS324 Bedienungsanleitung

Model No. WV-NS324Color CCTV CameraOperating InstructionsBefore attempting to connect or operate this product,please read these instructions carefully

-10-Cutout in Decoration CoverNote: Remove sharp edges to protect the cables.b. Top Cable ExitPrepare a hole in the ceiling board to run thecables.1.

-11-5. Tighten the fixing screw M3 (provided).Notes:(1) Tighten the camera fixing screw with a screw-driver.(2) Follow the instructions given here to

ContactInsertUpAApprox.3 mm (0.1 inch)Insert the wire until A positionand clamp the contacts.WireNote: When powered up, the unit performs a self-check

-13-•Ethernet ConnectionqRedData transmissionData receptionOrangeYellowGreenwertyuiTX +RX +RX –TX –• ALARM IN ConnectionsAn 8-pin and a 4-pin harness

-14-• Connection to Intranet (Type 2)A switching hub connected to the intranet is placedbetween the camera and the PC.Necessaries: • Straight-type net

-15-SETUP WITH PCNotes:• Do not access this menu through HTML or con-trollers during the Panasonic IP Setup procedure.• Only one administrator is requ

-16-PREPARATIONS FOR THE PC Network Setup of Your PCTo set up the network of the PC, first change the TCP/IPsettings of the PC to match them to the d

-17-7. Click the "Use the following IP address" radio but-ton and enter the IP address and the subnet maskas follows.IP address : 192.168.0.

-18-3. Click the [Setup Menu] button. The "User adminis-tration" window appears.• Enter "admin" in the user line.Note: The default

-19- Network Setup Parameters vs. Connection TypeConnection type Item Parameter descriptionConnection type 1 IP address Enter "192.168.0.XXX&quo

-2-WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposedto dripping

-20-Connection type Item Parameter descriptionConnection type 3 IP address Enter the IP address assigned by your Internet service provider.The setting

-21-Connection type Item Parameter descriptionHost name Contact your Internet service provider and enter the assigned hostname if required.Network spe

-22-3. Enter "admin" in the user name line. According tothe default setting, you need not enter the pass-word. The "Network Setup"

-23-You can operate the camera in two ways: with the PCby way of network, or with the Matrix Switcher systemcontrollers. Access from the PCYour PC can

-24-You can monitor pictures from multiple cameras on amultiscreen on the monitor multiscreenPictures of up to four cameras can be displayed as agroup

-25-• Function Comparison / PC Network vs. Camera siteFunction PC Network Camera Site (*1)VIEWING IMAGESPAN/TILT A AZOOM/FOCUS A AIRIS A APRESET A AAU

-26-This section describes setup procedures common toaccesses from the PC, e.g. transmitting images to anFTP server, sending alarm notice mail, auxili

-28--27- Setup MenuSetup menus are shown in the diagram below. These enable you to adapt the camera to your own requirements.The menus are described

-29-Function/ControllerOpen CAM SETUPOpen SpecialAll ResetF2 keyWV-CU550CJ WV-CU360C WV-CU161C WV-RM70See page 30CAM SETUPkey (for 2 sec-onds or more)

-30-The following setting procedures are described on theassumption that this model is used in combination withthe WJ-SX550C Matrix Switcher and WV-CU

-3-IMPORTANT SAFETY INSTRUCTIONS1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use th

-31-● Position Setting (POSITION SET)Aligns the camera position and focal point by panning,tilting, zooming and focusing.1. Move the cursor to POSITIO

-32-● Preset Identification Setting (PRESETID)Assigns a name to preset IDs (identification of up to 16alphanumeric characters) and can be switched on

-33-● Light Control Setting (ALC/MANUAL)Selects the ALC or MANUAL mode for adjusting thelens iris.1. The factory default setting is ALC.ALC: The lens

-34-3. Move the cursor to DEL and press the CAM (SET)key.This deletes the preset position and the PRESETNUMBER SET menu appears. The * mark to therigh

-35-3. Panning starting point and panning endpointFollow the steps below.(1) Move the cursor to POSITION and press theCAM (SET) key. The cursor moves

-36-Notes:• When the panning or tilting in the AUTO PANmode is controlled manually, the Auto modefunction should be cancelled.To activate the auto mod

-37- Camera SettingTo Display the Camera Setting MenuMove the cursor to CAMERA O, and press the CAM(SET) key. The camera setting menu appears.● Camer

2. Move the cursor to MASK SET and press theCAM (SET) key. The 48 mask areas appear onthe monitor screen. The cursor is blinking inthe top left corner

-39-6. If you want to change the video output level(picture contrast), move the "I" cursor forLEVEL and adjust the level.7. Move the cursor

-40-5. Move the cursor to COARSE by using the joystick.6. Match the vertical phases for both video output sig-nals as closely as possible by using the

-4-CONTENTSIMPORTANT SAFETY INSTRUCTIONS ...3PREFACE ...5

-41-2. For fine adjustment of the ATW, press the CAM(SET) key. The ATW fine adjustment menu appearson the monitor screen.3. Move the cursor to RET by

-42-Notes:•A scene magnified by the electronic zoomfunction may be inferior in picture quality to anon-magnified one.• The electronic zoom does not fu

-43-8. Dwell TimeMove the cursor to DWELL TIME, and select a timewith the Joystick.When the time specified here elapses after motiondetection, the cam

-44-(7) To Restore the Camera Default Position(REFRESH)Move the cursor to REFRESH by using the joystickand press the [F2] button of the WV-CU550CJ.For

-45-The camera setup menus overlaid on the camera picture appear by clicking the [Camera] button in the main window.You will be prompted by the authen

-46-The setup windows listed below are accessible with thePC. The operations in these windows are described onthe following pages.Click the setup menu

-47-Note: Input an external alarm signal of more than100 ms.3. Alarm PresetSelect the item by pressing the [o] button, andclick the [SET] button.1POSI

-48-1. Click the [FTP Client] button.2. Common Setup• Enter the FTP server address.A hostname.domainname can be enteredwhen using the DNS function.• E

-49- Host Setup1. Click the [Host] button.2. Host Authentication• Select [ON] or [OFF], and click the [SET] but-ton.ON: Applies the host authenticati

-50-4. Time zoneEnter the time difference between your siteand GMT.Settings from 0:00 to 13:00 are valid.Select +/– by pressing the [o] button, andcli

-5-Features• 10/100BASE-T terminal enables your PC to viewcamera images via the network.• Multiscreen function for simultaneous display of thepictures

-51- Auto Pan SettingClick the [Camera] button in the Setup menu, and thenclick the [Auto Pan] button.START POINT:1. Take the viewpoint as START POIN

You can reset the following data to the factory defaultsettings.Camera SetupHTML filesSetting the SwitchesThe camera is provided with an 8-bit DIP swi

-53- Still Picture Storage to the PCThe camera picture can be saved as a still image onyour PC.1. Move the cursor to the picture area on the screen,a

Pixelnumbers-54-When alarm arises, the camera performs output func-tions according to the setup.Inputs: • Input from ALARM IN 1 and ALARM IN 2.• Input

-55- Transferring Picture Files• Set FTP setup menu.• Pre- and post-alarm picture files can be sent to andstored on a designated FTP server.•A pictur

-56-5. Move the cursor to MASK SET, and click the [SET]button.The detection map is split into 48 areas with statusindications for each.Transparency: I

-57- Reviewing Alarm Pictures The alarm pictures stored in the camera can bereviewed on the PC.1. In the main window, click the [Alarm List] button.2

-58- Resetting Alarm You can reset the alarm output functions being activat-ed.1. In the main window, click the [Setup Menu] button.2. Click the [Ala

-59-File Name: almmail.tmpl, a template for alarme-mail notifications.Use the provided file name.Step 2Start up the Windows DOS prompt and connect byi

-60- Auxiliary Output ControlYou can turn a connected device on or off, for examplea lamp that is connected to the AUX OUT terminal ofthe camera.1. S

-6-• Distributing, copying, disassembling, reverse com-piling, reverse engineering, and also exporting inviolation of export laws of the software prov

-61-TROUBLESHOOTINGSymptomNo picture is displayed.HTML documents are not displayed.• Is the AC adapter firmly plugged in to the outlet?• Are the POWER

max. 4 times, AUTO/FIXON/OFF (SETUP MENU) selectable1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s16 V DC 100 mA, Low-activeIn

-63-Panning rangeZoom ratioFocus speedFocal lengthx10 + digital zoom x 5approx. 3.8 s (TELE/WIDE) in manual modeapprox. 3.0 s (FAR/NEAR) in manual mod

Selecting a PRESET position From #1 to #16#1 [1] + [CAM FUNC]#16 [1] + [6] + [CAM FUNC]AUTO PANON [6] + [5] + [CAM FUNC]OFF [6] + [6] + [CAM FUNC]Spee

N0303-0 3TR001552BAB Printed in JapanPANASONIC CANADA INC.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010PANASONIC SALES COMPANY

-7-1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screws orcovers.There are no user-serviceable parts inside.Ask

wertqyuoi!0-8-CONSTRUCTIONq Alarm Input Connectorw Alarm Output Connectore Video Output Connectorr Network Portt Power Cabley Camera Mounting Base (Co

Note: All DIP switches except SW1 and SW2 shouldalways be set to "off".3. Assemble the CameraReverse the disassembly procedure. Take care no