Panasonic WVCL920_SERIES Bedienungsanleitung

(Lens : option)WV-CL924CL924Before attempting to connect or operate this product,please read these instructions carefully and save this manual for fut

-10-2. 24 V AC Power SupplyConnect the power cable to the AC/DC compatibleinput terminal on the rear panel of the camera.Copper wire #24 #22 #20 #18si

-11-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

-12-Caution for Mounting the LensThe lens mount should be a CS-mount (1”-32UN). Incase of a C-mount, it should be a C-mount adapter andthe lens weight

-13-ScrewFlange-backAdjusting RingThe following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screw on th

-14-Fixing ScrewsMount Adapter• Mounting from the topRemove the mount adapter from the bottom of thecamera by removing the two fixing screws. Attacht

-17-WhiteBalanceATW1 ATW2 AWCMotionDetectorSpecialMenuDisplayModeCHROMAGAINUP SIDE DOWNAPGAINPEDESTALHUEBWBURST(BW)ON OFFCameraResettingManualMask A

-18-Note: If no button is pressed for 6 minutes while theCAM SET UP menu or any other menu is opened,the menu is automatically closed and the moderetu

-19-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): Moves the cursor upwards. Usethis button to select an item oradjust the paramet

-20-• Editing the CAM SET UP MenuImportant Notice:When SET UP DISABLE appears in the bottom lineof the CAM SET UP menu, you cannot change thecurrently

-21-1. Camera Identification (CAMERA ID)SettingYou can use the camera identification (CAMERA ID) toassign a name to the camera. The camera ID consists

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE.R

-22-2. Move the pointer to the character to be replaced bypressing or . Then move the cursor to thecharacter area and select a new character.3. Pres

-23-1. Move the cursor to the ALC/ELC parameter.2. Select ALC or ELC.Cautions: 1. Under bright lighting conditions such as outdoors,use an ALC type le

-24- ** ALC CONT ** BACK LIGHT COMPPRESET OFFMASK SET LEVEL ...I... - +RET END↵ ** ALC CONT ** BACK

-25-2. Move the cursor to MASK SET and press .The 48 mask areas appear on the monitor screen.The cursor is blinking in the top left corner of thescre

-26-3. Shutter Speed Setting (SHUTTER)Note: When ELC is selected for ALC/ELC on the CAMSET UP menu, this item is not available.You can select an elect

-27-5. Electronic Sensitivity Enhancement(SENS UP)There are two modes for SENS UP.AUTO: If you select x32 AUTO, for example, thesensitivity is raised

-28-Important Notices:1. The priority for the sync modes is as follows.1. Multiplexed Vertical Drive (VD2) (Highest priori-ty)2. Line-lock (LL)3. Colo

-29-3. Confirm that the INT parameter changed to EXT(VBS) on the menu.Caution: The gen-lock input signal should meet theCCIR specifications and should

-30-8. Adjust the horizontal phase by pressing or .The adjustable range is 0 - 2.0 µs.9. Move the cursor to SC COARSE.10. Press or to match the ch

-31-4. After confirming that the cursor is on EXT (VS),press . The phase adjustment menu appears onthe monitor.6-2. VS Gen-lock Mode (EXT(VS))1. Move

-3-CONTENTSPREFACE ... 4FEATURES ...

-32-2. After confirming the cursor is on LL, press . Thevertical phase adjustment menu appears on themonitor.3. Supply the video output signal of the

-33-• To reset COARSE and FINE to the values pre-set at the factory, press and simulta-neously. COARSE and FINE adjustments arepreset at the factory

-34-• Automatic White Balance Control Mode (AWC)In this mode, accurate white balance is obtainedwithin a colour temperature range of approximately2 30

-35-5. Press or to obtain the optimum amount ofblue gain.Note: When you need to set MASK SET, re-adjust toobtain the optimum amount of red and blue g

-36-Notes:• Masking or adjusting the detection level is neededto prevent malfunction under the following condi-tions:• When shooting an object under f

-37-10. Special Menu (SPECIAL)This menu lets you adjust and set up the video signal ofthe camera to meet your requirements.Move the cursor to END on t

-38-10-6. BW1. Move the cursor to the BW parameter.2. Select AUTO1, AUTO2, ON or OFF using or.Default: OFFAUTO1: The camera selects black and white m

-39-To reset to the factory settings1. Move the cursor to the CAMERA RESET parameter.PUSH SW is highlighted.2. While holding down and , press for 2

Pick-up Device: 762 (H) x 582 (V) pixels, Interline Transfer CCDScanning Area: 6.45 (H) x 4.84 (V) mm (Equivalent to scanning area of 1/2” pick-up tub

-41-Dimensions (without lens): 74 mm (W) x 55 mm (H) x 120 mm (D)[2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)]Weights (without lens): WV-CL920: 0.45 kg

-4-1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Back Light Compensation (Auto: Factory pre-se

-42-STANDARD ACCESSORIESBody Cap ... 1 pc.ALC Lens Connector (YFE4191J100) ...

-43-OPTIONAL ACCESSORIESLenses : WV-LA2.8, WV-LA4R5A, WV-LA6A, WV-LA12A, WV-LZ80/2, WV-LZ81/10, WV-LZ81/6, WV-LA4510, WV-LA608, WV-LA1208

2000 © Matsushita Communication Industrial Co., Ltd. All rights reserved.NM1100-0 V8QA5648AN Printed in JapanN 19Matsushita Electric Industrial Co.,

-5-1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screws orcovers.There are no user serviceable parts inside. As

-6-<WV-CL920><WV-CL924>WV-CL920FB LOCKFB LOCKHi-Z G/L 75ΩWV-CL920VIDEO OUTGEN-LOCK220-240V AC 50HzVIDEO OUTGEN-LOCKAC 24VINDC 12VINGND21

-7-q Auto Iris Lens ConnectorThis connector is used to connect the auto iris lenswith a 4-pin male connector supplied as a standardaccessory (Part No.

-8-!3 Power Cord SocketThis socket is used to connect the power cord(supplied as a standard accessory).!4 AC/DC Compatible Input Terminal(DC 12V IN/AC

-9-Copper wire #24 #22 #20 #18size (AWG) (0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010