Panasonic SC-BTT750 Bedienungsanleitung PDF herunterladen (Seite 19)

Getting started

VQT2W18

1 Select “Wired” or “Wireless” and press

[OK].

If “Wireless LAN Adaptor is not connected.” is displayed, check

that the Wireless LAN Adaptor is fully inserted. Alternatively,

disconnect and reconnect it. If there is still no change in the

display, consult your dealer.

2 Follow the on-screen instructions and

make the settings with [3, 4, 2, 1] and

press [OK].

For wireless LAN connection:

If you are using a Wireless router (Access point) that supports

WPS, you can easily perform the settings by selecting “WPS

(PUSH button method)”.

Otherwise, perform the settings by selecting “Search for

access point” or “Manual setting” in “Other methods”.

≥ WPS (Wi-Fi Protected Setup) is a function that facilitates

settings relating to the connection and security of wireless

LAN devices. To see whether your Wireless router (Access

point) supports WPS, check the Wireless router operating

instructions.

Access Point Connection Setting

Network Easy Setting (Connection Check)

Network Easy Setting

RETURN

Network Easy Setting (Connection Check)

Wired

Wireless

Select a connection mode.

Current setting : Wired

LAN cable connection:

Connect a LAN cable to the unit and select "Wired."

Wireless LAN connection:

Connect the Wireless LAN Adaptor (DY-WL10) to the USB

port and select "Wireless."

RETURN

Access Point Connection Setting

Select a connection method to use with an access point

of Wireless LAN.

Please refer to the operating instructions of the access

point about connection methods.

WPS (PUSH button method)

Other methods

WPS (PIN code method)

Search for access point

Manual setting

When you experience

problems with settings

Display Check the following

A conflict with another

device occurred.

≥ Please wait a few moments,

and then try again.

A time out error occurred.

≥ Setting of the Wireless

router (Access point) for

MAC Address etc.

≥ [BTT750] The signal may be

weak. Using the supplied

USB extension cable, adjust

the position of the Wireless

LAN Adaptor. Do not use

any other USB extension

cables except the supplied

one.

≥ [BTT350] The signal may be

weak. Using the USB

extension cable supplied

with the Wireless LAN

Adaptor, adjust the position

of the Wireless LAN

Adaptor.

≥ The SSID (> 20) and the

encryption key of the

Wireless router (Access

point).

≥ Please wait a few moments,

and then try again.

An authentication error or a

time out error occurred.

A device error occurred.

≥ Connection of Wireless LAN

Adaptor

If there is no improvement in

symptom, contact our

Customer Service Center.

Display

Check the

following

1. LAN cable connection or

Connection to access point

:Fail

≥ Connection of

the LAN

cables (> 16)

2. IP address setting :Fail

3. Connection to gateway :Fail

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection

Setting again ?

Yes No

Network Easy Setting (Connection Check)

Yes No

Complete.

1. LAN cable connection

2. IP address setting

3. Connection to gateway

LAN cable is not connected.

Please check the connection.

Select “Yes” and press [OK] to check network

connection again. Select “No” and press [OK]

to finish Network Easy Setting.

: Fail

SC-BTT750_350P_VQT2W18_eng.book 19 ページ２０１０年６月２１日　月曜日　午後４時５１分

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

Panasonic SC-BTT750 Bedienungsanleitung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Heimkinosysteme Panasonic SC-BTT750