OperatingInstructionsOutdoor Pan/Tilt HeadAW-PH650L1^ЦhE^^гM^ ^i------i6—i® #©"□------------------------------------□ "PanasonicBefore attem
Parts and theirfunctions Housing unit©© ©<D<The inside of housing>o ©©© oo Camera housing control boardConnect the supplied camera cable.©A
Parts and theirfunctions AC adapter unit© ©<The inside of AC adapter> Q©© © oQDC power unitThis unit supplies a DC output of15 V,10A (maximum) w
Parts and theirfunctions Supplied cable unit<Multi cablo (VEEB0133)oOoo©©©Q24P round water-proof plug (male)Connect this to the multi connector [MU
Parts and theirfunctions<Power cable> (VEEB0152)OoO7P round water-proof plug (female)Connect this to the power connector [POWER] on the main uni
Installation Installing the housing mount frameAttach the housing mount frame (supplied) to the rotary arm of the main unit.® Attach the housing mount
Installation Cable compensation circuit settingsWhen the pan/tilt head and controller have been connected, the maximum allowable length of the connect
Installation CPU circuit board switch settingsSet switches SW1, SW2 and SW3 on the CPU circuit board as follows.® SW1 (Selector switch for landing cha
Installation How to install the camera® Loosen the bolts for opening and olosing the top oover, and open the top oover.Loosen the top cover open/close
Installation<When the AW-E350 or AW-E650 camera is used>® Use the 2 screws © supplied with the camera to attach the mounting adapter O (supplied
Installation<When the AW-E655 camera is used>® Attach the positioning screw O (supplied) to the camera mounting spacer ©.@ Use the 2 screws © (s
ENGLISH VERSIONSafetyprecautions DO NOT REMOVE PANEL COVERS BY UNSCREWING.To reduce the risk of electric shock, do not remove the covers. No use
Installation<When the AK-HC1500 camera is used>® Attach the positioning screw© (supplied) to the camera mount ©.@ Attach the camera mount © usin
Installation<When a regular lens is used>® Sandwich the housing's support rib between the camera mount and plate nut of the camera on which
Installation<When a large lens is used>A large lens can be attached to the AK-HC910 or AK-HC1500, and stowed Inside the housing for use.In a cas
Installation© Check whether the ^^"-shaped part of the lens holder attached to the bottom of the lens Is Inside the elongated hole of the metal b
Installation How to install the housing® Align the mounting rails (O) on the bottom of the housing with the housing mount frame (©) on the main unit,
Connections Concerning the connectors inside the housingThe connectors shown in the figure below are provided inside the housing.Check the connection
Connections Connecting the cameras and housing1. Connections with a convertible camera® Use the supplied camera cable for these connections.@ Provide
Connections2. Connections with the AK-HC910 seriesIn order to faoilitate the oonneotion prooedure, stow the oamera after oonneoting its l/F REMOTE oo
Connections3. Connections with the AK-HC1500In order to faoilitate the oonneotion prooedure, stow the oamera after oonneoting its l/F REMOTE oonneoto
Connections Precautions when controlling the AK-HC1500 from the AW-CB400The AK-HC1500 supports the AK-HRP150 protocol and AW-CB400 protocol, and It Is
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)This symbol on the products and/or accompanying d
Connections Example of connections when using a convertible cameraThe AW-RP555 can also be used as the controller.29 (E)
Connections Example of connections when using a multi purpose cameraICamera controller AK-HRP150/AK-HRP900AC adapter AW-PS505AMonitor• Precautions whe
LimitersBe absolutely sure to set the limiters (travel range) of the pan/tllt head before use. Depending on where the pan/tllt head system has been In
Limiters Releasing the limitersThe set limits can be release by taking the following steps.• Releasing the upper limit of operating range1. While ho
Replacementofconsumable parts Replacing the batteryThe battery lasts for about 5 years.The pan/tilt head stores the preset positions, limiter positio
Replacementofconsumable parts Replacing the motorReplace the motor when it ceases to operate properly.For details on the motor replacement, consult y
Appearance Main unitUnit: mm213 237170190, 4-010 hole35 (E)
Appearance Housing unitUnit: mmCl I •)ii36 (E)
Appearance AC adapter unitUnit: mm20022 280 200=1TTTN> liiTJ------izr TT37 (E)
CO00?n"8n>o3io'&)o'o0)s?o-fB"^ The cable lengths are approximate. Ensure that their lengths are appropriate for the actual
ContentsIntroduction...3Accessories ...
COCD?n^ The cable lengths are approximate. Ensure that their lengths are appropriate for the actual system used."8n>oo'&)o'o0)s?
o?n"8n>o5o'&)o'o0)s?o-fB"^ The cable lengths are approximate. Ensure that their lengths are appropriate for the actual syst
SpecificationsPower supply: 220 to 240 V AC, 50HzPower consumption: 120 WI' 'I indicates safety information.Ambient operating temperature-2
l\DmENGLISH
Matsushita Electric Industrial Co., Ltd.Web Site: http://panasonic.net/Printed in Japan Gedruckt in Japan Imprimé au Japon Stampato in Giappone Impres
Installation precautions• Do not install this unit by suspending it, and do not install it on its side.• While faotoring in the weights of the unit
Mounting (Pan/tilthead) Precautions for installation• Do not install this unit by suspending it, and do not install it on its side.• Using the four pa
Mounting (ACadapter) Precautions for installation• Be sure to use water-proof oonneoting oables.• Be sure to keep AC power switohed off during insta
Mounting (ACadapter)@ Connect the cables. (Refer to the “Connections”.)Make the distance between the AC adapter and pan/tilt head less than the length
Parts and theirfunctions Main unit (Pan/tilt head)O©Q O ©QMain unit coverThe sunshade cover and main unit cover must be removed when the cable compens
Kommentare zu diesen Handbüchern